284 lines
9.0 KiB
C
284 lines
9.0 KiB
C
/* vim: set ai et ts=4 sw=4: */
|
|
#include "st7735.h"
|
|
|
|
#define DELAY 0x80
|
|
|
|
// based on Adafruit ST7735 library for Arduino
|
|
static const uint8_t
|
|
init_cmds1[] = { // Init for 7735R, part 1 (red or green tab)
|
|
15, // 15 commands in list:
|
|
ST7735_SWRESET, DELAY, // 1: Software reset, 0 args, w/delay
|
|
150, // 150 ms delay
|
|
ST7735_SLPOUT, DELAY, // 2: Out of sleep mode, 0 args, w/delay
|
|
255, // 500 ms delay
|
|
ST7735_FRMCTR1, 3, // 3: Frame rate ctrl - normal mode, 3 args:
|
|
0x01, 0x2C, 0x2D, // Rate = fosc/(1x2+40) * (LINE+2C+2D)
|
|
ST7735_FRMCTR2, 3, // 4: Frame rate control - idle mode, 3 args:
|
|
0x01, 0x2C, 0x2D, // Rate = fosc/(1x2+40) * (LINE+2C+2D)
|
|
ST7735_FRMCTR3, 6, // 5: Frame rate ctrl - partial mode, 6 args:
|
|
0x01, 0x2C, 0x2D, // Dot inversion mode
|
|
0x01, 0x2C, 0x2D, // Line inversion mode
|
|
ST7735_INVCTR, 1, // 6: Display inversion ctrl, 1 arg, no delay:
|
|
0x07, // No inversion
|
|
ST7735_PWCTR1, 3, // 7: Power control, 3 args, no delay:
|
|
0xA2,
|
|
0x02, // -4.6V
|
|
0x84, // AUTO mode
|
|
ST7735_PWCTR2, 1, // 8: Power control, 1 arg, no delay:
|
|
0xC5, // VGH25 = 2.4C VGSEL = -10 VGH = 3 * AVDD
|
|
ST7735_PWCTR3, 2, // 9: Power control, 2 args, no delay:
|
|
0x0A, // Opamp current small
|
|
0x00, // Boost frequency
|
|
ST7735_PWCTR4, 2, // 10: Power control, 2 args, no delay:
|
|
0x8A, // BCLK/2, Opamp current small & Medium low
|
|
0x2A,
|
|
ST7735_PWCTR5, 2, // 11: Power control, 2 args, no delay:
|
|
0x8A, 0xEE,
|
|
ST7735_VMCTR1, 1, // 12: Power control, 1 arg, no delay:
|
|
0x0E,
|
|
ST7735_INVOFF, 0, // 13: Don't invert display, no args, no delay
|
|
ST7735_MADCTL, 1, // 14: Memory access control (directions), 1 arg:
|
|
ST7735_ROTATION, // row addr/col addr, bottom to top refresh
|
|
ST7735_COLMOD, 1, // 15: set color mode, 1 arg, no delay:
|
|
0x05}, // 16-bit color
|
|
|
|
#if (defined(ST7735_IS_128X128) || defined(ST7735_IS_160X128))
|
|
init_cmds2[] = { // Init for 7735R, part 2 (1.44" display)
|
|
2, // 2 commands in list:
|
|
ST7735_CASET, 4, // 1: Column addr set, 4 args, no delay:
|
|
0x00, 0x00, // XSTART = 0
|
|
0x00, 0x7F, // XEND = 127
|
|
ST7735_RASET, 4, // 2: Row addr set, 4 args, no delay:
|
|
0x00, 0x00, // XSTART = 0
|
|
0x00, 0x7F}, // XEND = 127
|
|
#endif // ST7735_IS_128X128
|
|
|
|
#ifdef ST7735_IS_160X80
|
|
init_cmds2[] = { // Init for 7735S, part 2 (160x80 display)
|
|
3, // 3 commands in list:
|
|
ST7735_CASET, 4, // 1: Column addr set, 4 args, no delay:
|
|
0x00, 0x00, // XSTART = 0
|
|
0x00, 0x4F, // XEND = 79
|
|
ST7735_RASET, 4, // 2: Row addr set, 4 args, no delay:
|
|
0x00, 0x00, // XSTART = 0
|
|
0x00, 0x9F, // XEND = 159
|
|
ST7735_INVOFF, 0}, // 3: Invert colors
|
|
#endif
|
|
|
|
init_cmds3[] = { // Init for 7735R, part 3 (red or green tab)
|
|
4, // 4 commands in list:
|
|
ST7735_GMCTRP1, 16, // 1: Magical unicorn dust, 16 args, no delay:
|
|
0x02, 0x1c, 0x07, 0x12, 0x37, 0x32, 0x29, 0x2d, 0x29, 0x25, 0x2B, 0x39, 0x00, 0x01, 0x03, 0x10, ST7735_GMCTRN1, 16, // 2: Sparkles and rainbows, 16 args, no delay:
|
|
0x03, 0x1d, 0x07, 0x06, 0x2E, 0x2C, 0x29, 0x2D, 0x2E, 0x2E, 0x37, 0x3F, 0x00, 0x00, 0x02, 0x10, ST7735_NORON, DELAY, // 3: Normal display on, no args, w/delay
|
|
10, // 10 ms delay
|
|
ST7735_DISPON, DELAY, // 4: Main screen turn on, no args w/delay
|
|
100}; // 100 ms delay
|
|
|
|
static void ST7735_Select()
|
|
{
|
|
HAL_GPIO_WritePin(ST7735_CS_GPIO_Port, ST7735_CS_Pin, GPIO_PIN_RESET);
|
|
}
|
|
|
|
void ST7735_Unselect()
|
|
{
|
|
HAL_GPIO_WritePin(ST7735_CS_GPIO_Port, ST7735_CS_Pin, GPIO_PIN_SET);
|
|
}
|
|
|
|
static void ST7735_Reset()
|
|
{
|
|
HAL_GPIO_WritePin(ST7735_RES_GPIO_Port, ST7735_RES_Pin, GPIO_PIN_RESET);
|
|
HAL_Delay(5);
|
|
HAL_GPIO_WritePin(ST7735_RES_GPIO_Port, ST7735_RES_Pin, GPIO_PIN_SET);
|
|
}
|
|
|
|
static void ST7735_WriteCommand(uint8_t cmd)
|
|
{
|
|
HAL_GPIO_WritePin(ST7735_DC_GPIO_Port, ST7735_DC_Pin, GPIO_PIN_RESET);
|
|
HAL_SPI_Transmit(&ST7735_SPI_PORT, &cmd, sizeof(cmd), HAL_MAX_DELAY);
|
|
// SPI_Write(&cmd, sizeof(cmd));
|
|
}
|
|
|
|
static void ST7735_WriteData(uint8_t *buff, size_t buff_size)
|
|
{
|
|
HAL_GPIO_WritePin(ST7735_DC_GPIO_Port, ST7735_DC_Pin, GPIO_PIN_SET);
|
|
HAL_SPI_Transmit(&ST7735_SPI_PORT, buff, buff_size, HAL_MAX_DELAY);
|
|
// SPI_Write(buff, buff_size);
|
|
}
|
|
|
|
static void ST7735_ExecuteCommandList(const uint8_t *addr)
|
|
{
|
|
uint8_t numCommands, numArgs;
|
|
uint16_t ms;
|
|
|
|
numCommands = *addr++;
|
|
while (numCommands--)
|
|
{
|
|
uint8_t cmd = *addr++;
|
|
ST7735_WriteCommand(cmd);
|
|
|
|
numArgs = *addr++;
|
|
// If high bit set, delay follows args
|
|
ms = numArgs & DELAY;
|
|
numArgs &= ~DELAY;
|
|
if (numArgs)
|
|
{
|
|
ST7735_WriteData((uint8_t *)addr, numArgs);
|
|
addr += numArgs;
|
|
}
|
|
|
|
if (ms)
|
|
{
|
|
ms = *addr++;
|
|
if (ms == 255)
|
|
ms = 500;
|
|
HAL_Delay(ms);
|
|
}
|
|
}
|
|
}
|
|
|
|
static void ST7735_SetAddressWindow(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1)
|
|
{
|
|
// column address set
|
|
ST7735_WriteCommand(ST7735_CASET);
|
|
uint8_t data[] = {0x00, x0 + ST7735_XSTART, 0x00, x1 + ST7735_XSTART};
|
|
ST7735_WriteData(data, sizeof(data));
|
|
|
|
// row address set
|
|
ST7735_WriteCommand(ST7735_RASET);
|
|
data[1] = y0 + ST7735_YSTART;
|
|
data[3] = y1 + ST7735_YSTART;
|
|
ST7735_WriteData(data, sizeof(data));
|
|
|
|
// write to RAM
|
|
ST7735_WriteCommand(ST7735_RAMWR);
|
|
}
|
|
|
|
void ST7735_Init()
|
|
{
|
|
ST7735_Select();
|
|
ST7735_Reset();
|
|
ST7735_ExecuteCommandList(init_cmds1);
|
|
ST7735_ExecuteCommandList(init_cmds2);
|
|
ST7735_ExecuteCommandList(init_cmds3);
|
|
ST7735_Unselect();
|
|
}
|
|
|
|
void ST7735_DrawPixel(uint16_t x, uint16_t y, uint16_t color) //画点
|
|
{
|
|
if ((x >= ST7735_WIDTH) || (y >= ST7735_HEIGHT))
|
|
return;
|
|
|
|
ST7735_Select();
|
|
|
|
ST7735_SetAddressWindow(x, y, x + 1, y + 1);
|
|
uint8_t data[] = {color >> 8, color & 0xFF};
|
|
ST7735_WriteData(data, sizeof(data));
|
|
|
|
ST7735_Unselect();
|
|
}
|
|
|
|
void ST7735_DrawLine(int16_t x0, int16_t y0, int16_t x1, int16_t y1,uint16_t color) //画线
|
|
{
|
|
int16_t temp;
|
|
int16_t steep = abs(y1 - y0) > abs(x1 - x0);
|
|
if (steep) {
|
|
temp = x0;
|
|
x0 = y0;
|
|
y0 = temp;
|
|
|
|
temp = x1;
|
|
x0 = y1;
|
|
y1 = temp;
|
|
}
|
|
|
|
if (x0 > x1) {
|
|
temp = x1;
|
|
x1 = x0;
|
|
x0 = temp;
|
|
|
|
temp = y1;
|
|
y1 = y0;
|
|
y0 = temp;
|
|
}
|
|
|
|
int16_t dx, dy;
|
|
dx = x1 - x0;
|
|
dy = abs(y1 - y0);
|
|
|
|
int16_t err = dx / 2;
|
|
int16_t ystep;
|
|
|
|
if (y0 < y1) {
|
|
ystep = 1;
|
|
} else {
|
|
ystep = -1;
|
|
}
|
|
|
|
for (; x0 <= x1; x0++) {
|
|
if (steep) {
|
|
ST7735_DrawPixel(y0, x0, color);
|
|
} else {
|
|
ST7735_DrawPixel(x0, y0, color);
|
|
}
|
|
err -= dy;
|
|
if (err < 0) {
|
|
y0 += ystep;
|
|
err += dx;
|
|
}
|
|
}
|
|
}
|
|
|
|
void ST7735_FillRectangle(uint16_t x, uint16_t y, uint16_t w, uint16_t h, uint16_t color) //矩形填充
|
|
{
|
|
// clipping
|
|
if ((x >= ST7735_WIDTH) || (y >= ST7735_HEIGHT))
|
|
return;
|
|
if ((x + w - 1) >= ST7735_WIDTH)
|
|
w = ST7735_WIDTH - x;
|
|
if ((y + h - 1) >= ST7735_HEIGHT)
|
|
h = ST7735_HEIGHT - y;
|
|
|
|
ST7735_Select();
|
|
ST7735_SetAddressWindow(x, y, x + w - 1, y + h - 1);
|
|
|
|
uint8_t data[] = {color >> 8, color & 0xFF};
|
|
HAL_GPIO_WritePin(ST7735_DC_GPIO_Port, ST7735_DC_Pin, GPIO_PIN_SET);
|
|
for (y = h; y > 0; y--)
|
|
{
|
|
for (x = w; x > 0; x--)
|
|
{
|
|
HAL_SPI_Transmit(&ST7735_SPI_PORT, data, sizeof(data), HAL_MAX_DELAY);
|
|
// SPI_Write(data, sizeof(data));
|
|
}
|
|
}
|
|
|
|
ST7735_Unselect();
|
|
}
|
|
|
|
void ST7735_FillScreen(uint16_t color) //全屏填充
|
|
{
|
|
ST7735_FillRectangle(0, 0, ST7735_WIDTH, ST7735_HEIGHT, color);
|
|
}
|
|
|
|
void ST7735_DrawImage(uint16_t x, uint16_t y, uint16_t w, uint16_t h, const uint16_t *data) //画图像
|
|
{
|
|
if ((x >= ST7735_WIDTH) || (y >= ST7735_HEIGHT))
|
|
return;
|
|
if ((x + w - 1) >= ST7735_WIDTH)
|
|
return;
|
|
if ((y + h - 1) >= ST7735_HEIGHT)
|
|
return;
|
|
|
|
ST7735_Select();
|
|
ST7735_SetAddressWindow(x, y, x + w - 1, y + h - 1);
|
|
ST7735_WriteData((uint8_t *)data, sizeof(uint16_t) * w * h);
|
|
ST7735_Unselect();
|
|
}
|
|
|
|
void ST7735_InvertColors(bool invert) //反转颜色
|
|
{
|
|
ST7735_Select();
|
|
ST7735_WriteCommand(invert ? ST7735_INVON : ST7735_INVOFF);
|
|
ST7735_Unselect();
|
|
}
|